Autoignition temperature

The autoignition temperature or kindling point of a substance is the lowest temperature at which it will spontaneously ignite in a normal atmosphere without an external source of ignition, such as a flame or spark. This temperature is required to supply the activation energy needed for combustion. The temperature at which a chemical will ignite decreases as the pressure increases or oxygen concentration increases. It is usually applied to a combustible fuel mixture. Autoignition temperatures of liquid chemicals are typically measured using a 500 mL flask placed in a temperature controlled oven in accordance with the procedure described in ASTM E659.E659 – 78 (Reapproved 2000), "Standard Test Method for Autoignition Temperature of Liquid Chemicals", ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959

Autoignition equation

The time t_{ig}\, it takes for a material to reach its autoignition temperature T_{ig}\, when exposed to a heat flux q''\, is given by the following equation t_{ig} = \left ( \frac{\pi}{4} \right ) \left (k \rho c \right )\left \frac{T_{ig}-T_{o}}{q''} \right Principles of Fire Behavior. ISBN 0-8273-7732-0. 1998. where k = thermal conductivity (W/(m·K)), ρ = density (kg/m³), and c = specific heat capacity (J/(kg·K)) of the material of interest. T_{o} is the temperature, in kelvins, the material starts at (or the temperature of the bulk material), and q″ is the heat flux (W/m²) incident to the material. To be consistent in units the group \left \frac{T_{ig}-T_{o}}{q''} \right should be squared.

Autoignition point of selected substances

Temperatures vary widely in the literature and should only be used as estimates. Factors which may cause variation include partial pressure of oxygen, altitude, humidity, and amount of time required for ignition.

• Triethylborane:
• Silane:
• White phosphorus:
• Carbon disulfide:
• Diethyl ether: {{cite web |url=http://www.wolframalpha.com/input/?i=diethyl+ether

|title=Diethyl Ether - Safety Properties}} by Wolfram|Alpha curated data, 2009; Wolfram Mathematica ChemicalData

• Diesel or Jet A-1:
• Gasoline (Petrol): depending on grade
• Butane: {{cite web |url=http://www.wolframalpha.com/input/?i=butane

|title=Butane - Safety Properties}} by Wolfram|Alpha curated data, 2009; Wolfram Mathematica ChemicalData

• Paper: {{cite web

|url=http://books.google.com/books?id=qa-I8QAOUL8C&pg=PA406&lpg=PA406&dq=flash+point+of+paper&source=web&ots=FjB5FslcKK&sig=Vlr2cc8M2-TWy3qkdwzGUeK-vnM&hl=en&sa=X&oi=book_result&resnum=10&ct=result#PPA406,M1 |title=Handbook of Physical Testing of Paper |author=Jens Borch, Richard E. Mark, M. Bruce Lyne}} or 218°-246°C (424-474°F){{cite journal |url=http://www.tcforensic.com.au/docs/article10.html |title=Physical Constants for Investigators |author=Tony Cafe |journal=Journal of Australian Fire Investigators |note= Reproduced from "Firepoint" magazine - Journal of Australian Fire Investigators }}

• Magnesium:
• Hydrogen: {{cite web |url=http://www.wolframalpha.com/input/?i=hydrogen&a=*C.hydrogen-_*Chemical-

|title=Hydrogen - Safety Properties}} by Wolfram|Alpha curated data, 2009; Wolfram Mathematica ChemicalData For paper, there is considerable variation between sources. Part of this is because it takes longer for combustion to start at lower temperatures.{{cite web | url = http://www.fpl.fs.fed.us/documnts/fplmisc/rpt1464.pdf | title =IGNITION AND CHARRING TEMPERATURES OF WOOD | author =Forest Products Laboratory | year =1964 | publisher =Forest Service U. S. Department of Agriculture }}

See also

• Pyrolysis
• Flash Point
• Gas burner (For flame temperatures, combustion heat energy values and ignition temperatures)

References

External links

• Analysis of Effective Thermal Properties of Thermally Thick Materials.